HOME ABOUT US CONTACT US NEW MACHINERY USED MACHINERY FINANCING HOFMANN SEMINARS & PRESENTATIONS **LIQUIDATION SALE**
USED MACHINERY
Browse by Application:


View All 9 Photos      View Slideshow









1609-01

Brandt Edgebander, Servo w/ Premill & Corner Rounding

Model: KDF530C servo; SN: 0-261-02-xxxx; Year: 2005.
480v; 3ph; 60.


- PC:  Industrial PC, 600 Mhz, Front side USB port.
- Memory:  256 Mb ram, 1 Gb Flash Card.
- Screen:  12.1” Color, 800 x 600 pixel, Active TFT Screen
- Internal modem for remote diagnostic link
Equipped with digital height indicator.
Dual feed speed of 46 FPM / 36 FPM.  36 FPM when contour trimming.
Integrated electronic line control system for increased reliability and diagnostic assistance.  No limit switches used for setting operating units.
Universal automatic magazine for strip and coil feeding.
Large coil table (800 mm diameter) to accommodate large coils of 3 mm PVC.
Adjustable in feed fence.
Joint trimming unit with two diamond cutter heads.  For trimming the panel edge.
** IMPORTANT NOTE **  Although this machine is capable of running thicker panels, the pre-mill cutter heads on this machine are only 42 mm working height!  If pre-milling of panels thicker than 42 mm is desired, please obtain an alternate quote which includes 60 mm working height pre-mill cutter heads.
Hot melt granulate glue application system with approximately twelve minute heat-up time.  No lubrication required for maintenance.  
Reversible rotation of glue application roller.  Retractable glue roller.
Strengthened precutter for cutting PVC (max. 3 x 45 mm) from the coil.
Double motor end trimming unit with straight and chamfer capability.  Chamfer up to 15.  Program controlled indexing from straight to bevel.
Fine trimming unit with Servo Motor Program controlled indexing.  Equipped with 3-roller copy system instead of standard copy wheel to compensate for hinge cups.
Contour trimming unit.
Scraping unit with program controlled pneumatic indexing. Equipped with copy shoe instead of tracing wheel to compensate for hinge cups.
Buffing unit.
Electronic frequency changer for all trimming motors which also incorporates electronic motor brakes.
Electrical components according to UL/CSA Listings.
 
Technical Specifications
Edgeband thickness 0.4 - 8 mm (0.016" - .315") ( 5/16”)
Coil cutoff maximum 0.8 x 55 mm
3.0 x 45 mm (PVC)
Edgeband height 12 - 55 mm (1/2" – 2 3/16”")
Panel length min. 160 mm (6 3/8")
Panel width min. 65 mm (2 3/8")
Panel thickness - min.
                           - max. 8 mm (5/16") 
50 mm (2")
Feed speed 11/14 m/min (36 FPM when contour trimming otherwise 46 FPM )
Feed motor 2.2 kw (3 HP)
Joint trimming – two motors
    Cutting speed 2.2 kw ( 3 HP each motor )
12,000 RPM
Pressure section First roller driven, two rollers idle
End trim unit - two motors
     Cutting speed
     Straight cut max. .18 kw (1/4 HP)
12,000 RPM
8 x 45 mm (5/16" x 1 3/4")
Fine trimming unit
     Cutter speed .55 kw (3/4 HP ea.)
12,000 RPM
Contour trimming unit
      Cutting speed .35 kw ( ½ HP )
12,000 RPM
Electronic frequency inverter
Total power required 6 kw
Amperage @ 230
                   @ 460 50 amps
25 amps
Machine length 4770 mm (15’ 7”)
Machine width 1730 mm (68")
Working height 900 mm (35.5")
Total height 1600 mm (63")
Machine net weight (with all stations full) 2000 kg (4400 lbs.)
Electrical connection: 208/230 or 440/480 volt, 3-phase, 60 Hz.
Dust extraction: 1x 120 mm (4 3/4"), 3x 60 mm ( 2 3/8” ), 1x 100 mm (  4” ),  1400 CFM.
Compressed air connection:  0.18 CFM per panel, 6 bar (85 PSI).
PC-20 Program Control
Integrated Electronic Line Control System for Increased Reliability and Diagnostic Assistance

Equipped with digital height indicator.
Dual feed speed of 46 FPM / 36 FPM.  36 FPM when contour trimming.
Integrated electronic line control system for increased reliability and diagnostic assistance.  No limit switches used for setting operating units.
Universal automatic magazine for strip and coil feeding.
Large coil table (800 mm diameter) to accommodate large coils of 3 mm PVC.
Adjustable in feed fence.
Joint trimming unit with two diamond cutter heads.  For trimming the panel edge.

Hot melt granulate glue application system with approximately twelve minute heat-up time.  No lubrication required for maintenance.  
Reversible rotation of glue application roller.  Retractable glue roller.
Strengthened precutter for cutting PVC (max. 3 x 45 mm) from the coil.
Double motor end trimming unit with straight & 15* chamfer capability.  
Program controlled indexing from straight to bevel.
Fine trimming unit with Servo Motor Program controlled indexing.  
Equipped with 3-roller copy system instead of standard copy wheel to compensate for hinge cups.
Contour trimming unit.
Scraping unit with program controlled pneumatic indexing. Equipped with copy shoe instead of tracing wheel to compensate for hinge cups.
Buffing unit.
Electronic frequency changer for all trimming motors which also incorporates electronic motor brakes.
Electrical components according to UL/CSA Listings.
 
Technical Specifications

Edgeband thickness 0.4 - 8 mm (0.016" - .315") ( 5/16”)
Coil cutoff maximum 0.8 x 55 mm
3.0 x 45 mm (PVC)
Edgeband height 12 - 55 mm (1/2" – 2 3/16”")
Panel length min. 160 mm (6 3/8")
Panel width min. 65 mm (2 3/8")
Panel thickness - min.
                           - max. 8 mm (5/16") 
50 mm (2")
Feed speed 11/14 m/min (36 FPM when contour trimming otherwise 46 FPM )
Feed motor 2.2 kw (3 HP)
Joint trimming – two motors
    Cutting speed 2.2 kw ( 3 HP each motor )
12,000 RPM
Pressure section First roller driven, two rollers idle
End trim unit - two motors
     Cutting speed
     Straight cut max. .18 kw (1/4 HP)
12,000 RPM
8 x 45 mm (5/16" x 1 3/4")
Fine trimming unit
     Cutter speed .55 kw (3/4 HP ea.)
12,000 RPM
Contour trimming unit
      Cutting speed .35 kw ( ½ HP )
12,000 RPM
Electronic frequency inverter
Total power required 6 kw
Amperage @ 230
                   @ 460 50 amps
25 amps
Machine length 4770 mm (15’ 7”)
Machine width 1730 mm (68")
Working height 900 mm (35.5")
Total height 1600 mm (63")
Machine net weight (with all stations full) 2000 kg (4400 lbs.)

Electrical connection: 208/230 or 440/480 volt, 3-phase, 60 Hz.
Dust extraction: 1x 120 mm (4 3/4"), 3x 60 mm ( 2 3/8” ), 1x 100 mm (  4” ),  1400 CFM.
Compressed air connection:  0.18 CFM per panel, 6 bar (85 PSI).

PC-20 Program Control

Integrated Electronic Line Control System for Increased Reliability and Diagnostic Assistance

Return conveyor available seperatly.


$33,500.00


Replacement cost: $95,000.00, (approx.).
FOB: Hudson, NY
This machine is offered “in good running condition as taken from service” and is subject to prior sale.
Specifications are approximate and to the best of our knowledge. Verification is available upon request.